If left unpatched, CVE-2026-19576 could lead to major system disruptions or data loss.
Status: Received on 11 Oct 2026, 18:16 UTC
Published on: 11 Oct 2026, 18:16 UTC
CVSS Release: version 3
vulnerabilities@zephyrproject.org
Secondary
CVSS:3.1/AV:P/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H
CVE-2026-19576: The Goodix GT9xx input driver in drivers/input/input_gt911.c reads the touch point count from the controller's status register and masks it with GT911_TOUCH_POINTS_MSK (0x0F), yielding a value of 0..15. In gt911_process() that value is used directly as the loop bound for filling point_reg[], a stack array sized to CONFIG_INPUT_GT911_MAX_TOUCH_POINTS, whose Kconfig range is 1..5 with a default of 1. No other check constrains the count; the driver relied only on a comment asserting that the controller had been programmed at init to report no more points than configured. Each loop iteration issues an I2C read of eight bytes straight into point_reg[i], so a controller that reports more points than the array holds causes up to 112 bytes of peer-supplied data to be written past the end of the array, over the stack frame of gt911_process() in the system workqueue thread. Two further loops then read out of bounds from the same array. Triggering it requires control of, or the ability to substitute, the I2C touch controller — plausible on the many supported boards where the GT9xx panel is a pluggable display module or shield rather than an on-PCB part; a spoofed device need only answer the init probes with a supported product ID and a checksum-valid config blob. The same overflow can also occur non-adversarially, with a GT9271-class panel that ignores the driver's touch-count programming and reports up to ten points, or with bus corruption of the single status byte. The impact is an out-of-bounds stack write with fully attacker-chosen content executing at kernel privilege, i.e. potential control-flow hijack on the host MCU, in addition to out-of-bounds reads and crashes. The attack vector is physical/local hardware access only; there is no network, USB, or syscall path to the defect. The fix clamps the reported count with min() against CONFIG_INPUT_GT911_MAX_TOUCH_POINTS before any array indexing.
The exploitability of CVE-2026-19576 depends on two key factors: attack complexity (the level of effort required to execute an exploit) and privileges required (the access level an attacker needs).
With low attack complexity and no required privileges, CVE-2026-19576 is an easy target for cybercriminals. Organizations should prioritize immediate mitigation measures to prevent unauthorized access and data breaches.
A lower complexity and fewer privilege requirements make exploitation easier. Security teams should evaluate these aspects to determine the urgency of mitigation strategies, such as patch management and access control policies.
Attack Complexity (AC) measures the difficulty in executing an exploit. A high AC means that specific conditions must be met, making an attack more challenging, while a low AC means the vulnerability can be exploited with minimal effort.
Privileges Required (PR) determine the level of system access necessary for an attack. Vulnerabilities requiring no privileges are more accessible to attackers, whereas high privilege requirements limit exploitation to authorized users with elevated access.
Above is the CVSS Sub-score Breakdown for CVE-2026-19576, illustrating how Base, Impact, and Exploitability factors combine to form the overall severity rating. A higher sub-score typically indicates a more severe or easier-to-exploit vulnerability.
Below is the Impact Analysis for CVE-2026-19576, showing how Confidentiality, Integrity, and Availability might be affected if the vulnerability is exploited. Higher values usually signal greater potential damage.
Stay updated with real-time CVE vulnerabilities and take action to secure your systems. Enhance your cybersecurity posture with the latest threat intelligence and mitigation techniques. Develop the skills necessary to defend against CVEs and secure critical infrastructures. Join the top cybersecurity professionals safeguarding today's infrastructures.